HPC ink is benzene, toluene, xylene, low odor of environmentally friendly ink, PET and PC have good adhesion, after rolling and other post-processing has excellent heat resistance, and with the molding resin has a good Adhesive, it is suitable for the nameplate and other fine printing of the rolling molding with two liquid reactive type silk screen printing ink.
Product Usage
* IMD, IML products
* Easy to handle PET film and PC sheet rolling molding with the pattern printing.
* With acrylic, ABS, AS, PC resin, such as rolling molding.
Product Features
* Because it is two liquid reaction ink, can form heat superiority.
* After 90 ° heating conditions can be cured to the rolling forming.
* Excellent color series with weather resistance and heat resistance.
Dilution / curing agent mixture
* Mix the ink thoroughly before use.
* Diluent to HP003, HP705 solvent 10 ~ 15% as the standard, according to the printing conditions can make the appropriate adjustments.
* Excessive dilution or use of other solvents will reduce printability and adhesion.
Depending on the application, add 100 grams of ink according to the following addition of the amount of added after mixing.
Ink name | HP1 curing agent | HP2 curing agent |
ＨＰ | 10% | 15% |
* Can be used in the greenhouse at 25 degrees in about 4 to 5 hours.
* If the use of time may reduce the performance of the ink, please do not continue to use.
* For cleaning of printing screens, please use the company's (201) cleaning.
* Adjuvant HP650 anti-fouling agent; improve defoaming and leveling effect, please add 1 to 3% use.
Printing
* Suitable for T-200 ~ 300 mesh screen printing.
* When printing with T-250 mesh, the printing area per kilogram of ink is about 35 square meters.
Drying / curing
* Must be heated and dried. The standard drying conditions were carried out by drying the oven at about 10 minutes at 80 ° C, followed by printing the adhesive and then drying at 90 ° C to 100 ° C for 60 minutes.
* Due to the printing area, screen size, printing environment (temperature, humidity, etc.), dryer performance is different, dryness will change, must be tested before production and be confirmed.
Precautions:
* For the molding of vacuum forming, air pressure molding, metal mold molding, and the like, and the printing sheet is inserted into the metal mold and the injection molding resin is integrated into the calendering, the selection of printing material and pattern printing ink, printing conditions, printing Order, drying method, selection of forming resin, design of metal mold (type and position of plastic mouth, number of glue mouth) Condition setting at injection molding, etc. The comprehensive factor will affect the final performance. So please try to fully test, confirmed the best conditions and then batch use.
Fire law instructions
* Is the third category of dangerous goods, the third class of oil, the risk level of 3
Safe / safe
* To protect the skin from eyes, use safety gloves and fire eyes. If the ink is stained with skin, rinse thoroughly with soap and so on. In addition, if you enter the eyes, water (live warm water) full cleaning, please go to the hospital to receive a doctor's diagnosis.
* Please use the container after the full sealed on the cold dark place for custody.
* Please read this manual carefully before using this product, and then use it after understanding the responsibility of the user.
Product tolerance testing
Pilot projects | Test conditions | Experimental results |
Bonding | JIS K 5600-5-6: ISO2409 (crossed method), 1MM width 6 ⅹ 6, with3M 6100Tape stripping | 0（No peeling） |
Scratch resistance | JIS K 5600-5-6:ISO15184(Pencil method), weight 750g, the coating without scratch when the hardness | OK |
Heat resistance | ISO3248：80℃，400 hours, observe the appearance of the coating and stripping | No abnormality |
Hot water resistance | JIS K 5600-6-2:ISO2812-2，And immersed in hot water at 40 ° C for 48 hours to observe the appearance and peeling of the coating film | No abnormality |
Acid resistance | In 5% sulfuric acid in the bubble for 7 hours, observe the appearance of the smear and stripping | No abnormality |
Alkali resistance | In 5% of the naoh in the bubble for 24 hours, observe the appearance of the smear and stripping the situation | No abnormality |
Friction resistance | Learning friction resistance test, with KANAKIN3 cotton, 500g friction load 500 times to observe the appearance of smear. | No abnormality |
Alcohol resistance | Learning vibration resistance test, with KANAKIN3 cotton, 200g friction load observed 50 times the appearance of smear, | No abnormality |
Punching | With a punching machine | No abnormality |
Impact resistance | JIS K 5600-5-3 DuPont impact testing machine，50㎝/500g | No abnormality |
Material: easy to bond PET sheet (Dongshan company produced HK31WF)
Ink: HPC-070 White
Dilution: 10% HP-003 solvent, HP-1 curing agent%
Printed version: with T-250 mesh screen, dry conditions: with oven 90 ℃, 60 minutes
The results of the test of the above items are the result of the Company's test and are not guaranteed.
Reminder:
1, users in the use of this product, please read the instructions, and must test the suitability of different batches of ink, the actual test India, to confirm the qualified before use in bulk;
2, the above conditions in the tolerance test data for the test conditions under the test results, not as a guarantee value.
Dongguan City, a color of Chemical Technology Co., Ltd. www.yanseco.com Chen Jingli 15916853336
